Construction Parts

0.5" x 1.4", roll formed aluminum H-type hardboard siding joint connector. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. Pocket sizes typically range from 7/16" to 1/2". As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.5" x 2.2", roll formed aluminum H-type panel connector. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. Pocket sizes typically range from 5/16" to 1/2". As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

12" smooth stamped aluminum pre-painted outside corner. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. Pocket sizes typically range from 5/16" to 1/2". As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.5" x 2.3", roll formed pre-painted aluminum batten cover. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.8" x 0.4" x 1.3", roll formed prepainted aluminum J-trim. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. Pocket sizes typically range from 5/16" to 1-1/2". As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.3" x 1" x 1", roll formed prepainted aluminum J-trim. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. Pocket sizes typically range from 5/16" to 1-1/2". As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.5" x 3.5", roll formed metal starter strip. Starter strip is a required accessory to start many siding installation jobs. Starter strip is used at the bottom of each side of the home to lock the first course of siding in place. Typically the bottom of the starter strip (the part that the first bottom panel hooks on to) should be at least 1 in. Below the top of the foundation, but the lower the siding is installed, the better. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

1.5" x 2.2", roll formed pre-painted aluminum high rib batten. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

Coil stock is available in various lengths, widths and thicknesses. Common thicknesses are 0.018" to 0.026". Typical widths are 1" to 4" and lengths are 50 feet to 200 lineal feet. Pre-painted white is commonly used. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.5" x 12 ", roll formed pre-painted aluminum soffit. This profile is formed in pre-painted aluminum. Lances are added to provide ventilation. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

1.5" x 1.5", roll formed pre-painted aluminum F-mold. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

1.3" x 3.5", 12 gauge roll formed side rail bracket with holes in galvanized. This channel has a variety of applications, from connecting, to mounting, to supporting other components. It serves as a frame to hold conveyor rollers when placed back-to-back. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

2" x 3", roll formed aluminum light reflector. This profile is formed using highly reflective aluminum coil. The alloy, hardness and finish can vary for unique applications as quantities permit. Surfaces are usually smooth and holes or slots can be incorporated to eliminate secondary operations. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

1" x 18", 26 gauge stamped stiffener with holes in galvanized. This strip has a variety of applications, from connecting, to mounting, to supporting other components. It serves as a frame to support molded plastic or fiberglass. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.2" x 1.8", pittsburgh lock starter strip. Starter strip is a required accessory to start many siding installation jobs. Starter strip is used at the bottom of each side of the home to lock the first course of siding in place. Typically the bottom of the starter strip (the part that the first bottom panel hooks on to) should be at least 1 in. Below the top of the foundation, but the lower the siding is installed, the better. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.2" x 1.8", pittsburgh lock starter strip. Starter strip is a required accessory to start many siding installation jobs. Starter strip is used at the bottom of each side of the home to lock the first course of siding in place. Typically the bottom of the starter strip (the part that the first bottom panel hooks on to) should be at least 1 in. Below the top of the foundation, but the lower the siding is installed, the better. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.1" x 1", roll formed metal edge protector. When panels or sheets have rough edges, this protector is placed over the edges to protect against sharp areas. These profiles can be made in steel or aluminum. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

1.5" x 2.2", stamped aluminum batten end cap. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

2.5" x 8.5", stamped aluminum pre-painted outside corner. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. Pocket sizes typically range from 5/16" to 1/2". As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

1.8" x 11.5", stamped aluminum pre-painted 12 inch textured hardboard corner. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. Pocket sizes typically range from 5/16" to 1/2". As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

1.8" x 11.5", stamped aluminum pre-painted wood-grain 12 inch outside corner. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. Pocket sizes typically range from 5/16" to 1/2". As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

1.8" x 7.5", stamped aluminum pre-painted 8 inch siding corners. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. Pocket sizes typically range from 5/16" to 1/2". As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

1.8" x 7.5", stamped aluminum pre-painted textured corner. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. Pocket sizes typically range from 5/16" to 1/2". As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

5/16" pocket, roll formed aluminum H-type hardboard siding joint connector. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. Pocket sizes typically range from 5/16" to 1/2". As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

1-5/8" pocket roll formed pre-painted aluminum J-trim. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.5" x 2.4", roll formed metal starter strip. Starter strip is a required accessory to start many siding installation jobs. Starter strip is used at the bottom of each side of the home to lock the first course of siding in place. Typically the bottom of the starter strip (the part that the first bottom panel hooks on to) should be at least 1 in. Below the top of the foundation, but the lower the siding is installed, the better. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

1.5" x 2", roll formed metal drip edge. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.5" x 1.8", roll formed pre-painted metal batten cover. This profile is formed in pre-painted galvanized steel. The finish can either be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

8" textured, stamped aluminum textured pre-painted outside corner. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. Pocket sizes typically range from 5/16" to 1/2". As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.5" x 16 ", roll formed pre-painted aluminum soffit. This profile is formed in pre-painted aluminum. Lances are added to provide ventilation. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

1" x 4 to 10", roll formed pre-painted aluminum fascia. This profile is formed in pre-painted aluminum. Ribs are added to provide additional strength and reduce "oil canning" waviness. Widths typically range from 4" to 8". As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

1-3/4" pocket, roll formed pre-painted aluminum J-trim. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.3" x 11.8", stamped metal painted roof tab. This profile is formed in pre-painted or mill finish aluminum. The part fits below roof shingles to direct and drain water off a roof. If desired, the finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.3" x 11.8", stamped metal roof tab. This profile is formed in mill finish or pre-painted aluminum. The part fits below roof shingles to direct and drain water off a roof. If desired, the finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.5" x 3", roll formed metal starter strip. Starter strip is a required accessory to start many siding installation jobs. Starter strip is used at the bottom of each side of the home to lock the first course of siding in place. Typically the bottom of the starter strip (the part that the first bottom panel hooks on to) should be at least 1 in. Below the top of the foundation, but the lower the siding is installed, the better. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.3" x 0.4" x 1.1", roll formed pre-painted aluminum J-trim this profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.3" x 0.625" x 1.1", roll formed pre-painted aluminum J-trim. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.2" x 1.3" x 0.8", roll formed pre-painted aluminum L-trim. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

12" textured, stamped textured pre-painted outside corner. This profile is formed in pre-painted aluminum. The finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. Pocket sizes typically range from 5/16" to 1/2". As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

0.5" x 2.3", roll formed metal starter strip. Starter strip is a required accessory to start many siding installation jobs. Starter strip is used at the bottom of each side of the home to lock the first course of siding in place. Typically the bottom of the starter strip (the part that the first bottom panel hooks on to) should be at least 1 in. Below the top of the foundation, but the lower the siding is installed, the better. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.

2.6” high x 2” wide J-shape in 21 gauge white, pre-painted galvanized steel. This profile is used as an end stile component in an overhead door. As such, it provides framing support to bolster weak areas. The galvanized coating adds corrosion resistance. The white is cosmetically matched to other mating parts.the profiles are commonly mounted with fasteners or bolts. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available for OEM production requirements.

2.6” high x 2” wide J-shape in 21 gauge galvanized steel. This profile is used as an end stile component in an overhead door. As such, it provides framing support to bolster weak areas. The galvanized coating adds corrosion resistance. The profiles are commonly mounted with fasteners or bolts. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available for OEM production requirements.

2.6” high x 2” wide J-shape in 21 gauge white, pre-painted galvanized steel. This profile is used as a center stile component in an overhead door. As such, it provides framing support to bolster weak areas. The galvanized coating adds corrosion resistance. The white is cosmetically matched to other mating parts. The profiles are commonly mounted with fasteners or bolts. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available for OEM production requirements.

0.020" thick x 4” x 10”, roof tab. This profile is formed in pre-painted or mill finish aluminum. The part typically fits below roof shingles to direct and drain water off a roof. If desired, the finish can be primed for re-painting, or color matched if quantities permit. Surfaces can be smooth or textured to match a wood-grain pattern. As a coil-based process, economical production quantities begin around 5,000 lineal feet. Custom lengths are available to meet OEM requirements.